For TP4056 5V 1A Micro USB 18650 Lithium Battery Charging Board Module TP-4056 by HAYATEC (Pack of 2)

Great little boards, used initials to recycle 18650 lithium batteries out of failed laptop batteries, work great and have a charging and charged led which is a great feature. Have recently also used them to recycle li-po batteries out of discarded vape pens I kept finding whilst walking the dog. Successfully replaced in devices that used two AA batteries and also made the device usb rechargeable.

After my sons wireless radio was dropped the charger port broke off from the pcb along with the tracks so I couldn't easily replace it like for like, so I purchased some of these and hot glued it to the pcb ran a micro usb lead to the old hole and it was as good as new.

Works fine as a charging board. I used it for 18650 powering WiFi extender. Re-soldering smd resistor to change charging current limit is a nuisance, but typical for tp4056 module. However, over discharge protection works at 2.5 - 2.6V. At this voltage your LiPo battery is already damaged. But Li-Ion can be discharged down to 2.5 and tp4056 was designed as Li-Ion charging circuit.

A GOOD PRODUCT AT A GOOD PRICE.

Read a lot of reports stating these wouldn`t do 2x 18650 in parallel. ~THEY DO. Ripped the batteries out an old laptop wired them up to this. Charged with zero issues.. ( admittedly i was sleeping with one eye open just incase hahaha ). But, over a month of charging various batteries in various devices. ( perfect to use with the bluetooth modules ).. all good,...!! PI-ZERO USERS I have one of these connected to my raspberry pi ZERO. Charging up a random 1000mha ( not 18650 ), and its going super strong. You can still use the pi, as its charging.

Very good charging curent - pushes up to 4.23V in the lithium cells however they heat up like they’re about to burn, even with one lithium battery cell (18650) charging from a 1 A charger. Other than the heat, it’s a very good product.

Used to temporarily revive the battery in a Switch console that had charge port damage. Worked well. Don't need 5 but at this price can't complain! Be careful which type of Li-ion battery you try and charge with it though as there are a lot of different types and this is designed for particular battery formulations/chemistry.

Nice little unit, ideal for charging a Lithium ion battery cell . It has a red LED for charging and green when charged. I have had one socket detach from the board, too fiddly to solder back as the track ripped due to a stiff plug to socket.

ممتاز ورائع ويوجد بها دائره حمايه ضد القفله... واجمل حاجه عند البائع انى هو الوحيد اللى بيبعها رخيصه له جزيل الشكر.....

جيد

برده ممتازة وليها استخدامات كتير بما ان البائع مش شارح حاجة عن البرده هشرح انا البرده بتحمى البطارية من الشحن الزايد فوق 4.2 فولت و الشحن الناقص تحت 2 فولت اقصى قدره شحن هى 1 امبير بس مش كل البطاريات بتحتاج انها تتشحن ب 1 امبير علشان تحمى البطارية من التلف لازم تغير المقاومة R3 بمقاومة المناسبة لقيمه البطارية فى معادلة رياضيه علشان تعرف بيها انت محتاج تغير المقاومة R3 لمقاومة قيمتها كام

جيد

جميله ومفيده بس الناس تخلى بلها لان الخمس قطع بيجو متجميله ومفيده بس الناس تخلى بلها لان الخمس قطع بيجو متصلين ببعض وبتم فصلهم لانى أنا ادجالى المنتج قبل كده من نفس المورد وكان ثلاثه لازقين مع بعض واثنين لازقين مع بعض وقمت بارجاعهم وكتبت تعليق أن المنتج غير المعروض وده كان خطاء منى لانه لما بيجوا بيكون ا متصليين ونحن نقوم بقطمهم وفصلهم من بعض صلين ببعض وبنقوم بفصلهم لانى أنا جالى المنتج قبل كده من نفس المورد وكان ثلاثه لازقين مع بعض واثنين لازقين مع بعض وقمت بارجاعهم وكتبت تعليق أن المنتج غير المعروض وده كان خطاء منى لانه لما بيجوا بيكون متصليين ونحن نقوم بقطمهم وفصلهم من بعض